The message on the PRO-97 display comes up when you plug the cable into its PC/IF jack. After you plug the USB end into your PC, I go into device manager to see what COM port is assigned.
The Radio Shack Pro-97 is a high-performance, extended-coverage scanner has the ability to scan both trunked and conventional channels at the same time. Program up to. I don't think you have any words on the display when programming a PRO-97. I still have one and gave one to a buddy that still has analog Trunked Radio System. I use WIN97 to program it and never had issues. Radio Shack Pro 94 ProgrammingYou'll need to select that in WIN97. Note that the scanner doesn't know about software. When you plug in a cable, it thinks you are going to clone it with another PRO-97. You do NOT need to press buttons on the scanner to use WIN97. Once you have your programming entered into WIN97, select 'upload to scanner'. You'll see progress on the PRO-97 display or an error message on the PC. Let us know what happens or what the error message is. Pro-97 Cheat Sheet If system is Motorola Type II, EDACS or LTR start with Programming section, if Motorola Type I or IIi, set the fleetmap in the last section prior to Programming. Storing known trunked frequencies 1. Press MANual, Press three digits to get the bank and channel number desired then Press MANual again. National gypsum fire resistance design manual. In addition, all of its cement facilities completed their planned annual outages during the first quarter and cement maintenance costs were approximately US$3m higher than the prior year's first quarter. Gypsum wallboard and paperboard revenues for the first quarter totalled US$136m, which were slightly lower than the same quarter of 2015. (Upper left should read Mxxx for your bank and channel number) 2. Press PGM, (upper left should change from M to P) 3. Press TRUNK 4. Press MODE to Mot/ED*/LT* depending on system. On Motorola 800 MHz systems press Func then 3 and choose either Standard or Splinter (for border areas) 5. Enter the frequency 7. Press Enter 8. Radio Shack Pro-97 Step-by-Step LTR Programming Guide Written by David Cabatu, AH7E INTRODUCTION This white page will give you step-by-step instructions to program the Radio Shack Pro-97 scanner to properly receive LTR type radio systems. Do keep in mind that your scanner can only decode non-digital (in order words, analog only) transmissions. Repeat steps 5 through 8 until all frequencies are entered in selected bank. * EDACS & LTR systems must be programmed in Logical Channel Number (LCN) order. * Be sure to begin programming EDACS or LTR frequencies in channel 1 not channel 0. Leave channel 0 blank. Note: if frequency Alpha Tags are desired, use step 3 through 5 in Storing known Text Tags below between step 7 & 8 above. Press SCAN Storing known Talkgroup ID’s 1. Press TRUNK 3. Enter the 5 digit for Mot, or 4 digit/AFS X-XXX for ED, or AFS X-XX- XXX for LTR. Press ENTER 5. Press Up button 6. Repeat steps 3, 4 and 5 until all are entered. Note: if TG Alpha Tags are desired, use step 3 through 5 in Storing known Text Tags below between step 4 & 5 above. Storing known Text Tags 1. Navigate to the bank with the trunked system. Press PGM then TRUNK, then navigate up/down to the first ID to tag. Press Text, the cursor appears on line 3. Using the numbered keys text in the line up to 16 characters. The letters above each number will help in the selection. Example, POLICE DISPATCH (15 characters counting the space) The first letter is P, Press the number 7 then the number 1 for P. (7 will open the four numbers PQRS and by selecting 1 is for the first of these four. A 7 then 2 would get the letter Q. Press up or down to move the courser back and fourth or to correct a mistake. Press Enter A chart in the Owners Manual may be used for other options. Programming Fleetmaps 1. Restrict your radio to scanning the bank that contains the Motorola system that needs the fleetmap programmed, using the method previously shown. Press MANual 3. Press FUNC then TRUNK, this puts the scanner in the Talkgroup programming mode. Press FUNC then 8, this your Fleetmap screen and should be default Type II (Block 0 size code. Use 15 for type II S-00. The S is for size and the 00 is for Type II system in this block. Using the information for your system, enter the 2-digit number for the first block, i.e., 04 for 4 etc. Press ENTer, the new block number will appear (remember about size code 12, 13 and 14 previously discussed). Repeat steps 5 and 6 until all 8 blocks are entered. Note: After pressing ENTer on block #7, the radio will return to the Talkgroup programming screen 8. Martin solveig all stars. Using the numbered buttons, key in your 1st tag. ) for ( - ) Press ENTer. Repeat step 8 until all are entered (30 per each of the 5 sub-banks) A final note on Type 1 size codes: Many systems use size code 12 but size code 13 or 14 are rare. This white page will give you step-by-step instructions to program the Radio Shack Pro-97 scanner to properly receive Ericsson EDACS type radio systems. Do keep in mind that your scanner can only decode non-digital (in order words, analog only) transmissions. Also, it is also important that you follow all instructions in order. If something doesn’t g o your way, you may have overlooked something in this list of instructions. A lot of hard work and effort has gone into the testing and writing of this document. I would appreciate it if every effort is made to keep this document whole with me as the original author. Of course, it doesn’t hurt that this document is copyrighted and therefore protected by U.S. Law and international treaties governing intellectual property. Except for personal use, no part of this work may be reproduced in any form or by any means, or stored in a database or retrieval system, without prior permission of the author. If you have any questions, or would like to share any thoughts with me, please send me some e-mail. Thank you and enjoy! FAILURE TO PROPERLY SET GROUP ID TO EDACS MODE WILL CAUSE YOUR SCANNER TO TRACK IMPROPERLY. Press [PGM], [TRUNK ]. The top line of the display changes to ONE of the following: ID Bank 0 -- If trunking mode is NOT selected. ID Bank 0-1 ON -- If trunking bank IS selected. Press [MODE] until EDACS appears on the third line. This indicates that the trunking mode is correctly set to EDACS. How Do You Program A Radio Shack Pro 97 Scanner ReviewsPress [PGM] to return to frequency programming mode. The display should read P001FM 0.00000, with 'P' indicating that you are in programming mode. A) If the display reads P00xFM, and 'x' does NOT equal '1', press the UP/DOWN arrow keys to set it a ccordingly. B) If the display reads M00xFM, you are in MANUAL mode. Press [PGM ] to return to programming mode. ALL EDACS PROGRAMMING MUST BEGIN IN CHANNEL X01 OF A BANK 'X'. Using the LCN frequencies above, follow steps 1-5. Enter LCN-1, Press [8] [6] [6] [.] [2] [5] [0] [0] [ENTER]. Press [MODE] until the display reads P001ED, indicating that EDACS mode is set for that frequency. Press [PGM] to move to the next channel. Check step B3b above if the display does NOT read P00x (to program LCN-x). Enter the rest of the frequencies in LCN order, following steps 1 through 3 above. Radio Shack Pro 97 SoftwarePress [SCAN] to begin trunk tracking. If your scanner is programmed correctly, active talkgroup IDs will be displayed in decimal format until you assign a text tag to it. If you don't hear anything after a few minutes of listening, the scanner just hasn't found the control channel. You can press [SCAN] to quicken the process. Also, make sure that you do not lock out the control channel. To program other banks, follow all steps in Parts B and C. The number of steps will vary depending on how many channels need to be programmed in that bank. Talkgroup IDs are programmed in numerical order from lowest to highest. All analog talkgroup IDs h ave been programmed with alpha tags so when moving into a new repeater area, you will only need to reprogram the frequencies in LCN order, rather than reprogramming frequencies and talkgroup IDs with their associated alpha tags. Press [PGM], [TRUNK ]. The second line of the display shows EDACS TGID#xx. Enter talkgroup IDs using the keypad. Radio Shack Pro 97 AntennaYou can enter them using one, two, three, or four digits. I suggest entering them in four digit blocks since the display defaults to four digits. Example: Enter the HFD DISP talkgroup ID, 785. Press [0] [7] [8] [5] [ENTER]. The scanner accepts the talkgroup.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |